User Manual of Hatari AC Turbo1 Air Cooler

by 
User Manual of Hatari AC 
Turbo1 Air Cooler

 

Hatari AC Turbo1 Air Cooler User Manual

FAN COMPONENTS

  1. CORD WINDER
  2. CONTROL AND DISPLAY PANEL
  3. WIND DIRECTION SHUTTERS
  4. FRONT COVER
  5. WATER TANK
  6. WATER LEVEL WINDOW
  7. WHEELS (2 back wheels with brakes)
  8. PRE-FILTER
    • SIDE 2 PIECES
    • BACK 1 PIECE
  9. SIDE GRILLES
    • SIDE 2 PIECES
  10. WATER DIFFUSING PLATE
    • SIDE 2 PIECES
    • BACK 1 PIECE
  11. WATER TANK LID
  12. GEL PACK COMPARTMENT
  13. POWER SUPPLY CORD WITH PLUG
  14. WATER DRAIN LID
  15. REMOTE CONTROL
  16. GEL PACK 2 PIECES

 

Hatari AC Turbo1 Air Cooler - FAN COMPONENTS

DIRECTION OF USE

This fan is operated by touch screen system and remote control. Touch screen system can be activated using fingers to touch the control and display panel. Remote control, point the remote signal transmitter in the direction of the signal receiver on the control and display panel. Avoid having obstructions between the remote signal transmitter and the receiver. Plug the power supply cord into a 220V, 50Hz power socket.

 

Hatari AC Turbo1 Air Cooler - DIRECTION OF USE

  1. ON/OFF: Touch the switch on the control and display panel to turn on the fan. The light will show the resumed settings of the fan’s latest operation before having been switched off. To turn the fan off, touch the switch again for about 1.5 seconds (When the air cooler is switched off while the COOL function is activated, the fan will continue to operate for 1 minute to remove moisture. The fan will stop working immediately afterwards).
  2. SPEED: 5 adjustable fan speed settings 0: off,1: lowest speed, 2: low speed, 3: medium speed, 4: high speed, 5: highest speed, respectively.
  3. TIMER: Switch for timing the fan’s operation: 1, 2, 4, 8 hours or to cancel timing altogether, respective to the number of time the sensor is touched. Once set, the timer will indicate the remaining time left of the duration.
    3.1 TIMER OFF : Set the timer while the fan is switched on to set the time when the fan is to automatically turn off.
    3.2 TIMER ON : Set the timer while the fan is turned off (but it must be plugged in) to set the time when the fan is to automatically turn on. When the time comes, the fan will resume settings of the latest operation before having been switched off.
  4. COOL: Switch for activating the water cooling system. Touch the switch to activate the function. Touch the switch again to deactivate the function.
  5. SWING: Switch for adjusting left to right swinging motions. Touch the switch to activate the function. Touch the switch again to deactivate the function.
  6. DIMMER: Dimmer switch for the control and display panel. Touch the switch (while the operating lights are on) to reduce the brightness of the control and display panel. Press the switch again or any other control function to resume the standard broghtness level. (This function is controlled by remote control only)
  7. NIGHT: On/off button, light on the control and display panel. Press the button on the remote control. to turn off the light on the control and display panel. Press the switch again or any oter control function to resume the standard broghtness level. (This function is controlled by remote control only)
  8. FILL WATER: A warning will light up when the water level in the tank is too low for the water distribution system to function (unable to activate COOL function). Turn off and unplug the machine to fill the water tank with clean water (do not exceed MAX level). The warning light will go off when the machine is turned on and the COOL function is activated.
  9. ELCB: A warning with a warning sound will appear when there is electricity leakage. The circuit breaker system will immediately be activated.
  10. TEMPERATUER: Temperature display for surrounding area of the fan, While the fan is turned off or on (but it must be plugged in).

HOW TO REPLACE THE REMOTE CONTROL BATTERY

 

Hatari AC Turbo1 Air Cooler - HOW TO REPLACE THE REMOTE CONTROL BATTERY

Open the battery cover by using your fingernail to push the catch downwards as shown by the arrow and remove the battery cover. Replace the used batteries with new “AAA” batteries, ensuring that the positive (+) and negative (-) poles are correctly inserted and correspond with the symbols on the remote control. Place the battery cover back in its original position.

*Batteries should be removed from the remote control when not in use for a long period of time.

CAUTION caution icon

  1. Unplug the supply cord before filling water, cleaning or changing the components, and when not in use for a long period of time.
  2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experiences and knowledge, unless they have been given supervision or instruction concerning use of the appliance.
  3. Children should be supervised to ensure they do not play with the appliance.

HOW TO REMOVE THE PRE-FILTER FOR CLEANING

Pre-filter (BACK)

 

Hatari AC Turbo1 Air Cooler - Pre-filter (BACK)

  1. Use a screwdriver to loosen the screws holding the pre-filter in place. Use your hands to press the locks located at the top to remove the pre-filter for cleaning.
  2. To insert the pre-filter, use your hands to press the locks located at the top of the pre-filter and carefully push to lock it in place. Use a screwdriver to tighten the screws holding the pre-filter in place.

Pre-filter (SIDE)

 

Hatari AC Turbo1 Air Cooler - Pre-filter (SIDE)

  1. Use a screwdriver to loosen the screws holding the grille in place. Use your hands to press the locks located at the top of the grille to unlock it. Lift the grille upwards to free it from the latches in the middle and remove the pre-filter for cleaning.
  2. To replace the pre-filter within the side grilles, flip the side grille upward and place the pre-filter in place within the frame boundary (A) ensuring that the side with the arrow is at the top.
  3. Insert the grille from the top, ensuring that the latches in the middle fit with those of the grille on bothsides. Use your hands to press the locks located at the top of the grille and carefully push to lock it. Use a screwdriver to tighten the screws holding the grille in place.

USAGE RECOMMENDATIONS read icon

  1. The fan should not be placed or installed in areas that are of extreme temperatures or near stoves, or in areas that are wet with high humidity, or has hydrocarbon vapors such as petroleum.
  2. Do not spray all types of spray into the fan; for example, hairspray or cleaning spray.
  3. Do not insert fingers, pencils or other objects into the grille while the blades are spinning as it may result in possible injury or physical damage.
  4. If an electrical component such as supply cord, motor, or switch is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. It is not advisable to fix the fan at home.
  5. The fan must always be placed vertically; it must never be lying horizontally or placed upside down. If the fan falls down, unplug it immediately and lift the fan up to a vertical standing position. Use a cloth to wipe the fan and leave it to dry in order to prevent electrocution.

CARE AND CLEANING INSTRUCTIONS

  1. Use a damp cloth to wipe stains, and then dry the area by wiping.
  2. When cleaning, be careful not to let the supply cord, switch, motor, and other electrical components get wet.
  3. Do not use chemical products, thinner solvents, alcohol, kerosene or petrol to clean the fan.
  4. The water tank, pre-filter, grilles, and water tank can be cleaned with water or soapy water. It should be cleaned at least every 1-2 months.

USAGE PRECAUTIONS

Use only clean water to fill the water tank. Do not use any other liquid. The water tank should be cleaned regularly to reduce bacteria buildup.

 

Hatari AC Turbo1 Air Cooler - USAGE PRECAUTIONS