LIVARNO Under Cabinet LED Light Instruction

by 
LIVARNO Under Cabinet LED Light Instruction

LIVARNO Under Cabinet LED Light Instruction Manual

LIVARNO Under Cabinet LED Light Instruction Manual - Product Overview

LIVARNO Under Cabinet LED Light Instruction Manual - List of pictograms used

Under-cabinet LED light

Introduction

Congratulations on your new product. You have selected a high quality product. Please read carefully and completely through these operating instructions. These instructions form part of the product and contain important information about bringing the product into use and its handling. Always observe all the safety advice. Check that the correct mains voltage is available and that all the parts have been properly assembled before bringing into use. Should you have any questions or be uncertain as to how to operate the device, please get in touch with your dealer or service point. Please keep these instructions in a safe place and hand them on to a third party if necessary.

Proper use

LIVARNO Under Cabinet LED Light Instruction Manual - House iconThis light is suitable only for interior use, in dry and enclosed spaces.
The light should be positioned within reach so that the switch can be operated conveniently. The light can be fitted to all normally inflammable surfaces. Any use other than that described above or modification to the lamp is not permitted and may lead to damage to people or property. Moreover, there is the risk of injury or loss of life and that the lamp may develop technical faults such as short circuit or fire or give an electric shock. This lamp is intended for use only in a domestic environment. This product is intended for normal operation.

Included items

Check that all the items and accessories are present and that the lamp is in perfect condition immediately after unpacking.

1 Under-cabinet LED light, Model 14137306L
1 Mains cable
1 Connection lead
2 Wall plugs
2 Clips
2 Screws
1 Set of assembly instructions and instructions for use

Description of parts
  1. Wall plug
  2. Clip
  3. Screws
  4. Cap
  5. Power cable
  6. Light connection
  7. ON / OFF switch
  8. Connection cable
  9. Light connection socket
Technical data

Operational voltage: 230­240 V 50 Hz
Bulb: 43 LEDs
Nominal output: max. 8 W
Dimensions: 57.3 x 3.0 x 2.2 cm  (L x W x H)
Protection class: II
Protection type: IP20

Safety

⚠ Safety advice

The right to claim under the guarantee shall be rendered invalid in respect of damage caused by the non-observance of these operating instructions! No liability is accepted for consequent damage! No liability is accepted for damage to property or persons caused by improper handling or no observance of the safety advice!

LIVARNO Under Cabinet LED Light Instruction Manual - Danger to life and accident iconDANGER TO LIFE AND ACCIDENT HAZARD FOR TODDLERS AND SMALL CHILDREN! Never leave children unsupervised with the packaging materials. The packaging material poses a suffocation hazard. Children frequently underestimate dangers. Please always keep the product out of the reach of children. This device may be used by children age 8 years and up, as well as by persons with reduced physical, sensory or mental capacities, or lacking experience and / or knowledge, so long as they are supervised or instructed in the safe use of the device and understand the associated risks. Do not allow children to play with the device. Cleaning and user maintenance must not be performed by children without supervision.
To avoid danger to life from electric shock

  • Before connecting it to the mains, always check the light, the power cable as well as the connecting cable if need be for any damage. Never use the light if you see any damage.
    Damaged power cables and connecting cables are a danger to life as you could suffer an electric shock. Before assembly, ensure that the mains voltage available corresponds to the operating voltage necessary of the light (see “Technical data”).
  • Never let the lamp come into contact with water or other liquids.
  • Never open or insert anything into electrical fittings or equipment. Doing this sort of thing can lead to a serious danger to life from electric shock.
  • Touch only the insulated part of the plug when connecting to or disconnecting from the mains supply.
  • If the external flexible cable of this lamp is damaged, it may only be replaced by a special cable or a cable that is only available from the manufacturer or his service representative.
  • Only connect the under-cabinet light to the mains current using the original power cable.
  • Only connect original under-cabinet lights of the same type with each other. Only use the original connecting cable supplied to do so.
  • Connect the under-cabinet lights that are linked up together to one socket only. Make sure that you only connect a maximum of 10 linked-up under-cabinet lights of the same type to one socket. Otherwise this might overload the connections and cables.
  • Make sure that all under-cabinet lights are linked up via connecting cables before inserting the power cable into the socket.
  • Do not install the lamp on damp or conductive surfaces.
  • Do not kink the power cable.
  • Do not lay the cable on sharp corners.

⚠ To avoid danger of fire and injury

  • RISK OF INJURY! Check every bulb and lampshade for damage immediately upon unpacking. Do not operate the light with a defective bulb or glass cover. If they are, contact the service point for a replacement.
  • Allow the light to cool off completely.
  • Do not look directly into the light source (lamp, LED, etc.).
  • Do not look at the LEDs with an optical instrument (e.g. magnifying glass).
  • The light bulb is not replaceable. If the illuminate has reached the end of its life, the entire light must be replaced.
  • RISK OF INJURY FROM BURNS! Ensure the lamp has been switched off and allowed to cool before you touch it. In this way you will avoid the danger of burns. Light bulbs develop a great deal of heat.
  • LIVARNO Under Cabinet LED Light Instruction Manual - Risk of injury from burns iconDo not use this lamp for external dimmers and electronic switches. It is not suitable for this mode of operation.
  • Never leave the light operating unattended.
  • Do not allow any objects to cover the light. Fire can result from the development of too much heat.
  • Do not allow the lamp or the packaging materials to lie around unattended. Plastic film or bags, Styrofoam etc. can turn into dangerous toys for children.
    Working safely
  • Fit the light in such a way to ensure it is protected from damp and dirt.
  • Make careful preparations for the assembly and take sufficient time. Clearly lay out all components and any additional tools or materials that might be required so that they are readily to hand.
  • Remain alert at all times and always watch what you are doing. Always proceed with caution and do not assemble the lamp if you cannot concentrate or feel unwell.

Preparation

Required tools and materials

The tools and materials mentioned are not included in the delivery. The details and values given are non-binding and for guidance only. The nature of the material depends on the individual circumstances on site.

– Pencil / Marking tool
– Drill
– Screwdriver
– Spirit level
– Electric drill
– Measuring tape

Preparations for use

Fitting the light

Note: Prior to installation, verify there is a socket nearby within reach of the included power cable 5 .

  1. Measure up the wall or mounting surface for drilling the holes. Use a spirit level to improve accuracy.
  2. Mark the distance between the two mounting holes.
  3. Now drill the mounting holes (ø approx. 6 mm, depth approx. 30 mm). Make sure that you do not damage any electrical cables during this operation.
  4. Insert the supplied wall plugs 1 into the drilled holes.
  5. Screw the clips 2 tightly using the screws 3 (see Fig. A).
  6. Press the lights into the tightly screwed clips 2 (see Fig. B).
  7. Place the connector of the power cable 5 onto the light connection 6 .
  8. Insert the mains plug of the mains lead into a convenient mains socket. Your light is now ready for operation.
Connecting several lights together

CAUTION! Ensure that all the under-cabinet lights are connected before you insert the power cable 5 into the mains socket. Note: Make sure that you only connect a maximum of 10 linked-up under-cabinet lights of the same type to one socket.
Install up to 10 lights of the same model next to each other. To do so, follow steps 1­5 of the section called “Fitting the light”. Note: Make sure that the distance between the lights is not more than 16 cm.

  1. Insert the connector of the power cable 5 into the light connection 6 of the first light.
  2. Carefully remove the cap 4 of the light connection socket 9 using a screwdriver.
  3. Insert the connecting cable 8 into the light connection socket 9 .
  4. Insert the second connection of the connection cable 8 into the light connection 6 of the next light.
  5. Alternatively, you can directly connect the lights to each other by connecting the lights through the light connection socket 9 to the light connection 6 .
  6. Insert the mains plug into the mains socket. Your lamp is now ready to use.
Switching on / off

Switch the ON / OFF switch 7 to turn the light on or off.

Maintenance and cleaning

⚠ DANGER OF ELECTRIC SHOCK! Unplug the mains plug from the socket.
⚠ DANGER OF ELECTRIC SHOCK! For electrical safety, never clean the light with water or other liquids, nor immerse it in water.

  • Do not use solvents, benzene or similar substances. They could damage the light.
  • Allow the light to cool off completely.
  • Only clean with a dry, lint-free cloth.
  • Reinsert the mains plug into the socket after cleaning.

Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

LIVARNO Under Cabinet LED Light Instruction Manual - Disposal

Information

Guarantee

You receive a 36 month warranty on this product, valid from the date of purchase. The device has been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect arising during the warranty period, please send the device to the listed Service Centre address, making reference to the following model number: 14137306L. Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Declaration of conformity

This product conforms to the requirements of the applicable European and national directives. Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Manufacturer / Service

Briloner Leuchten GmbH & Co. KG Im Kissen 2 59929 Brilon GERMANY
Tel.: +49 29 61 / 97 12­800
Fax: +49 29 61 / 97 12­199
E-Mail: kundenservice@briloner.com
www.briloner.com

Free service number: Tel.: 00800 / 27456637

IAN 352698_2010
When inquiring about your product, please have your receipt and product number (e.g. IAN 123456_7890) ready as your proof of purchase.

LIVARNO Under Cabinet LED Light Instruction Manual - QR Code
www.lidl-service.com

BRILONER LEUCHTEN GMBH & CO. KG
Im Kissen 2
59929 Brilon
GERMANY

Last Information Update
12/2020 · Ident.-No.: 14137306L122020-8