HILTI SL 2-22 LED work light Instruction
Original operating instructions
1 Information about the documentation
1.1 About this documentation
- Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product.
- Observe the safety instructions and warnings in this documentation and on the product.
- Always keep the operating instructions with the product and make sure that the operating instructions are with the product when it is given to other persons.
1.2 Explanation of symbols
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words are used:
⚠ DANGER
DANGER ! Draws attention to imminent danger that will lead to serious personal injury or fatality.
⚠ WARNING
WARNING !
Draws attention to a potential threat of danger that can lead to serious injury or fatality.
⚠ CAUTION
CAUTION ! Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the equipment or other property.
1.2.2 Symbols in the operating instructions
The following symbols are used in these operating instructions:
1.2.3 Symbols in illustrations
The following symbols are used in illustrations:
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols can be used on the product:
1.4 Product information
products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products. This personnel must be specifically informed about the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product.
Product information
1.5 Declaration of conformity
The manufacturer declares, on his sole responsibility, that the product described here complies with the applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this documentation. The technical documentation is filed here: Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D86916 Kaufering, Germany
2 Safety
2.1 Important safety instructions
⚠ Warning! Read all instructions. Failure to follow all instructions listed below can result in electric shock, fire and/or serious injury.
Keep these instructions in a handy yet secure place.
▶ Use the product and accessories only when they are in perfect working order.
▶ Never tamper with or modify the product or accessories in any way.
▶ Persons with reduced physical, sensory or mental abilities or lack of experience and knowledge are not permitted to use this product.
▶ Children must receive instruction and be supervised to ensure that they do not play with the product.
▶ Do not use the product where there is a risk of fire or explosion.
▶ Do not use the product outdoors.
▶ To reduce the risk of electric shock, do not use the product in wet weather, immersed in water or in any other liquid.
▶ Do not expose the product to rain or moisture. Water entering the
product will increase the risk of electric shock.
▶ Replace the complete cordless lamp when the light source has reached the end of its life. The light source in this cordless lamp is not replaceable.
▶ Do not look directly into the light source and do not aim the beam at other persons’ faces.
▶ A falling product can constitute a risk of injury for you and others. Secure the area in which you will be working.
▶ Before each use, check all attachment points on the product and make sure they are in full working order.
▶ Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed accessories are secure.
▶ Before each use, check the flip-up hook to ensure that it is in perfect condition. Whenever you use the flip-up hook, make sure that the product is securely attached.
2.2 Battery use and care
▶ Comply with the following safety instructions for the safe handling and use of Li-ion batteries. Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.
▶ Use only batteries that are in perfect working order.
▶ Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely harmful to health!
▶ Do not under any circumstances modify or tamper with batteries!
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C (176 °F).
▶ Never use or charge a battery that has suffered an impact or been damaged in any other way. Check your batteries regularly for signs of damage.
▶ Never use recycled or repaired batteries.
▶ Never use the battery or a battery-operated power tool as a striking tool.
▶ Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This can lead to explosions.
▶ Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects. This can damage the battery and also cause material damage and personal injury.
▶ Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits, electric shock, burns, fire and explosions.
▶ Use only chargers and power tools approved for the specific battery type. Read and follow the relevant operating instructions.
▶ Do not use or store the battery in explosive environments.
▶ If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the document entitled “Instructions on safety and use for Hilti Li-ion batteries”.
ℹ Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries. page 10 Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning the QR code at the end of these operating instructions.
3 Description
3.1 Product overview 1
- LED
- Lamp head
- Multi-position hinge
- Flip-up hook
- Automatic switch
- Mode switch (light intensity)
- Grip
- Installation opening for accessories
- Battery
- Battery release button
- Battery status indicator
3.2 Intended use
The product described is a cordless lamp. It is intended for use as illumination on jobsites. Use the product in a dry environment only.
- For this product, use only Hilti Nuron lithium-ion batteries of the B 22 series. For optimum performance, Hilti recommends the batteries stated in the table at the end of these operating instructions for this product.
- For these batteries, use only Hilti chargers of the type series stated in the table at the end of these operating instructions.
3.3 Items supplied
Cordless lamp, operating instructions. Other system products approved for use with this product can be found at your local Hilti Store or at: www.hilti.group
3.4 Status indicators of the Liion battery
Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and the battery’s state of health.
3.4.1 Indicators for state of charge and fault messages
⚠ WARNING Risk of injury by a falling battery! If the release button is pressed with a battery inserted in the product, subsequently check that the battery is correctly re-engaged and secure.
Short-press the release button of the battery to get whichever of the following status indications is applicable at the time. State of charge and, if applicable, faults are indicated constantly as long as the connected product is switched on.
3.4.2 Indicators showing the battery’s state of health
To check the battery’s state of health, press the release button and hold it down for longer than three seconds. The system does not detect a potential malfunction of the battery due to misuse, for example battery dropped or pierced, external heat damage, etc.
4 Technical data
4.1 Product
4.2 Battery
5 Operation
⚠ CAUTION Risk of damage to the eyes (the retina). Looking directly into the lamp presents a risk of damage to the eyes (the retina).
▶Do not direct the lamp at yourself or at anyone else.
▶Do not, under any circumstances, look into the lamp.
Observe the safety instructions and warnings in this documentation and on the product.
5.1 Charging the battery
- Before charging the battery, read the operating instructions for the charger.
- Make sure that the contacts on the battery and the contacts on the charger are clean and dry.
- Use an approved charger to charge the battery. page 5
5.2 Inserting the battery
⚠ WARNING
Risk of injury by short circuit or falling battery!
▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product are free of foreign matter.
▶Make sure that the battery always engages correctly.
- Charge the battery fully before using it for the first time.
- Push the battery into the product until it engages with an audible click.
- Check that the battery is seated securely.
5.3 Removing the battery
- Press the battery release button.
- Remove the battery from the product.
5.4 Turning the lamp head
Turn the lamp head to the desired position.
ℹ The lamp head can be turned in either direction along the axis. Do not attempt to force the lamp head past the end stops.
5.5 Switching on / off
- Turn the lamp head to the desired position. page 8
- Select a mode by repeatedly pressing the mode switch.
▶ Brightness 100 %
▶ Brightness 50 %
▶ Off - To switch off, repeatedly press the mode selector until the light source of the cordless lamp goes out.
5.6 Fall arrest
⚠ WARNING
Risk of injury by falling tool and/or accessory!
▶ Use only the Hilti tool tether recommended for your product.
▶ Prior to each use, always check the attachment point of the tool tether for possible damage.
▶ Do not secure a tool tether to the belt hook. Do not use a belt hook to lift the product
ℹ Comply with the national regulations for working at heights.
As drop arrester for this product, use only a combination of the Hilti retaining strap and the Hilti tool tether #2261970.
▶ Secure the retaining strap to the installation openings for accessories. Check that it holds securely.
▶ Secure one carabiner of the tool tether to the retaining strap and secure the second carabiner to a load-bearing structure. Check that both carabiners hold securely.
ℹ Comply with the operating instructions of the Hilti retaining strap and those of the Hilti tool tether.
6 Care and maintenance
⚠ WARNING
▶ Risk of injury with battery inserted ! Always remove the battery before carrying out care and maintenance
tasks!
Care of the product
- Carefully remove stubborn dirt.
- Carefully clean the air vents, if present, with a dry, soft brush.
- Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
- Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries
- Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.
- Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of moisture (e.g. by being dipped in water or left in the rain). If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable container and consult Hilti Service.
- Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents containing silicone as these can attack the plastic parts. Do not touch the contacts of the battery and do not remove the factory applied grease from the contacts.
- Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as these can attack the plastic parts.
Maintenance
- Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly.
- Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product repaired by Hilti Service.
- After cleaning and maintenance, install all guards and protective devices and check that they are in full working order.
ℹ To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with your product can be found at your Hilti Store or online at: www.hilti.group
7 Transport and storage of cordless tools and batteries
Transport
⚠ CAUTION Accidental starting during transport !
▶ Always transport your products with the batteries removed!
▶ Remove the battery/batteries.
▶ Never transport batteries loose and unprotected. During transport, batteries should be protected from excessive shock and vibration and isolated from any conductive materials or other batteries that may come in contact with the terminals and cause a short circuit. Comply with the locally applicable regulations for transporting batteries.
▶ Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged batteries.
▶ Prior to each use and before and after prolonged transport, check the product and the batteries for damage.
Storage
⚠ WARNING Accidental damage caused by defective or leaking batteries !
▶ Always store your products with the batteries removed!
▶ Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in the technical data.
▶ Do not store batteries on the charger. Always remove the battery from the charger when the charging operation has completed.
▶ Never leave batteries in direct sunlight, on sources of heat, or behind glass.
▶ Store the product and batteries where they cannot be accessed by children or unauthorized persons.
▶ Prior to each use and before and after prolonged storage, check the product and the batteries for damage.
8 Troubleshooting
If a problem occurs, always observe the charge-status and fault indicator of the battery. See the section headed Status indicators of the Liion battery. If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by yourself, contact Hilti Service.
9 Manufacturer’s warranty
▶ Please contact your local Hilti representative if you have questions about the warranty conditions.
10 Disposal
⚠ WARNING
Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.
▶ DO NOT send batteries through the mail!
▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.
▶ Dispose of your battery out of the reach of children.
▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public health and safety resources for disposal instructions.
♻ Most of the materials from which Hilti products are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.
Do not dispose of power tools, electronic equipment or batteries as household waste!
11 Further information
For more information on operation, technology, environment and recycling, follow this link: qr.hilti.com/manual/?id=2265886?id=2265888 This link is also to be found at the end of the documentation, in the form of a QR code.
EC Declaration of Conformity I UK Declaration of Conformity
Manufacturer:
Hilti Corporation
FeldkircherstraBe 100
9494 Schaan I Liechtenstein
lmporte,,
Hilti (Gt. Britain) Limited
1 Trafford Wharf Road, Old Trafford
Manchester, M17 1BY
SL 2-22 (02)
Serial Numbers: 1-99999999999
Serial Numbers: 1-99999999999
2014/30/EU I Electromagnetic Compatibility Regulations 2016
2011/65/EU t The Restriction of the Use of
Certain Hazardous Substances in Elect rical and
Electronic Equipment Regulations 2012
EN 60598-1:2015 +
A1:2018
EN 60598-2-8:2013
EN 62493:2015
EN 55015:2013 + A 1 :2015
EN 61547:2009
Hilti Corporation
Ll-9494 Schaan
Tel.:+423 234 21 11
Fax:+423 234 29 65
www.hilti.group
Hilti = registered trademark of Hilti Corp., Schaan
Pos. 8 | 20220103