MODELS LISTED BELOW MUST BE EQUIPPED WITH SWC.
CHRYSLER
2011 – 2013 200
2007 – 2010 300
2007 – 2009 Aspen
2007 – 2010 PT Cruiser
2007 – 2010 Sebring
2008 – 2013 Town & Country
DODGE
2007 – 2013 Avenger
2006 – 2012 Caliber
2008 – 2013 Challenger
2006 – 2010 Charger
2005 – 2011 Dakota
2004 – 2013 Durango
2009 – 2013 Grand Caravan
2009 – 2010 Journey
2005 – 2008 Magnum
2007 – 2010 Nitro
2006 – 2012 Ram
JEEP
2006 – 2010 Commander
2007 – 2013 Compass
2005 – 2013 Grand Cherokee
2008 – 2010 Liberty
2007 – 2013 Patriot
2007 – 2013 Wrangler**
MITSUBISHI
2006 – 2009 Raider
VOLKSWAGEN
2009 – 2013 Routan
THIS INTERFACE DOES NOT SUPPORT AMPLIFIED SYSTEMS:
USE PART: BEECR-35P (AMP VERSION)
Vehicles listed above must have the “GRAY” 22-Pin connector. Radio type does not matter.
Applications are subject to change without notice.
BLUETOOTH CONNECTIVITY FOR SELECT CHRYSLER, DODGE, JEEP VEHICLES 2004-UP
we recommend reading this installation guide first before starting any work. Following these instructions from “Start” to” Finish” will ensure a smooth and hassle free installation. We offer telephone suppoer M-F 9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) CR-35 Interface Module
(1) CR-35 T-Harness
(1) Instruction Sheet
(1) Microphone
PRECAUTIONS:
– Remove the negative side of the battery to avoid any short circuits during the installation.
– Do not install the interface near any major components or near the HVAC system. This may cause damage or overheating to the vehicle.
Phone- Specific Note for iPhone 5S/iOS7 & Up:
Siri Voice command may not respond properly. Standard Voice command may have to be used instead.
PRELIMINARY:
Please read the entire manual before installing this interface.
THIS INTERFACE STREAMS THE HANDS-FREE & MUSIC (A2DP) THROUGH THE TWO FRONT SPEAKERS ONLY.
INSTALLING THE INTERFACE
- Remove the factory radio from the dashboard.
- Remove the factory connectors from behind the factory radio.
- Mate the interface connections to the factory connectors. Make sure the 22-pin connector is properly seated into the interface.
- Route the microphone to your desired location. Recommended are is above the rear-view mirror.
- Test the interface first, then re- install the radio into the dash.
ENABLE VOICE DIAL AND MENU STRUCTURE
TO ENABLE VOICE DIAL:
Place DIP switch 1 to ON. (As shown below)
NOTE:
If Voice Dial is enabled, the SWC function will change as follows:
- A short press (tap) of the TUNE DOWN button will perform a “SEEK”.
- A long press of the TUNE DOWN button will activate the Voice Dial command on the paired phone.
MOUNTING THE MICROPHONE
- Insert the mounting clip into the ball joint on the microphone.
- Mount the clip on your visor or near the rear view mirror.
- Route the remaining cable along the edge of the roof liner and towards the back of the radio, hiding the cable from sight.
10 AND 12-PIN CONNECTORS
IMPORTANT: The GRAY 12-PIN CONNECTOR ATTACHED WITH THE BLACK 10-PIN CONNECTOR GO TO THE BLUETOOTH MODULE ONLY.
INSTALLATION OVERVIEW
INITIAL PAIRING
- Turn on the vehicle and wait 15 seconds until the interface announces “Please Select Your Mobile Phone” and Enter “0000”
- From your mobile phone, choose and connect to the “Beeline” device using the password “0000”.
- The interface will announce “Pairing Successful” then “Phone Connected” after the pairing process is complete.
Note: The Bluetooth interface will remember up to the last 8 devices.
Note: If pairing is unsuccessful after several attempts power off then power back on to re-attempt, if unsuccessful please contact our tech support line.
AUTO RE-CONNECT
The BEELINE module will automatically re-connect the a previously paired mobile phone when the ignition is turned “ON” to the vehicle and the mobile phone’s Bluetooth feature is also on.
Note: The Bluetooth module will re-connect with the last mobile phone’s it was paired with. If no mobile phone is found, it will revert to the pairing process.
STEERING WHEEL CONTROLS
All Bluetooth functionality is done on the steering wheel controls.
BACKSIDE CONTROLS
All functionality are done on the steering wheel controls.
RADIO CONTROL
There is no Bluetooth control on the factory radio.
All controls are done from the steering wheel controls.
HOW TO ENTER THE MENU STRUCTURE
Preliminary: Disconnect from the beeline device or turn Bluetooth Off on the mobile phone.
1. Hold Seek Down For 2 seconds on the SWC and release.
Note: to toggle between choices press seek down. You are now at the top of the menu structure. Here are your options:
a. Setting Volume – this controls the Beeline voice prompts.
To adjust the volume, press and release the volume +/ – buttons. (In 1 second increments) Press Seek Down to set the desired volume setting. There are a total of 15 levels from the highest to lowest.
b. Delete Paired Phones – this deletes all phones on the Beeline memory. You will be asked to confirm this option, if so simply press the Seek Up button once. To cancel press Seek Down.
Note: The System Menu will time-out after 6 seconds of no activity. If so, please begin at step one from above.
HANDS-FREE FUNCTIONALITY
*Mobile phone must support Voice Dial for the function to work
RADIO VOLUME
While connected to the Bluetooth interface the steering wheel controls will only adjust the volume on the BT’s built in amplifier. The volume knob on the factory radio will remain the master volume control and will not change when adjusting the volume on the SWC.
COMPATIBLE RADIOS
NOTES
Note: If an incoming call is answered from the mobile phone’s keypad, the call will direct itself to the headset on the mobile phone. To re-direct the phone call to the “BEELINE”, it must be done directly from the mobile phone.
Note: When transferring a phone call to the mobile phone for privacy, the user must re-connect the BEELINE and the mobile phone by selecting the module from the device menu on the phone.
iPhone Note: The Bluetooth interface will disconnect from the mobile phone as soon as the key hits the off position. The call will be transferred to the mobile phone. The module will power down in 15 seconds after the car shuts off or drive door is opened.