AGCO PARTS 664M Automatic Preservative Applicator Installation
Introduction
Thank you for purchasing a HayBoss G2 Model 696M Hay Preservative Applicator. This 696M applicator system has been designed to plug directly into the baler’s ISOBUS and display on a C1000 monitor. As well as the option of operation through an Apple iPad (not included) using the Hay App. The 696M Preservative Applicator System offers these advantages:
- Operation coordinated with baler operation
- Less cab clutter providing better visibility
- Ease of use with all information on one screen
- Records kept together
- And the system is ready for future updates.
This manual will take you through the steps for installing the automatic applicator. If you are unsure about installing the system after consulting this manual, please contact your local authorized dealership for additional assistance. If you are in need of parts for the system please see the parts breakdown in the back of this manual and contact your local authorized dealer to order the parts. Right and Left sides are determined by facing in the direction of forward travel.
System Requirements
The Baler Processor must have Version 3.3 or higher. C1000 must have version 3.0.1 or higher
*Requirement to run iPad option are 3rd Generation iPad (2012) or newer, running the current iOS operating system or one version previous. Krone ISOBUS integration requires harness 006-6650VAK.
**600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest Tec for a required update in order to use the iPad Integration Module (030-6670C).
*Hay App version must be at least 2.5.18 (or higher) to operate with the iPad Integration Module (030-6672C) If choosing to operate the unit though the ISOBUS monitor, pn 006-6670A will need to be ordered through your local equipment dealer. 2018 Krone balers (and beyond) Serial Number 976909 will need pn 006-6650VAK.
Tools Needed:
– Standard wrench set
– Side cutter
Installation of Controls and Harnesses
1. Installation of Dual Channel Processor (DCP)
The Dual Channel Processor (DCP) has the same bolt pattern as the Precision Information Processor (PIP) you will be removing. The location of the main controller does not change so use the same holes and install the new Dual Channel Processor (DCP) in the same location with two 5/16″ x 1″ bolts, two 5/16″ x 1-1/4″ bolts, locks, fender washers and hex nuts. Mount the DCP cover over the top of the DCP and secure with the hardware using the 5/16″ x 1-1/4″ bolts on the top with the DCP shield.
DCP or PIP Location
2. Main Wire Harness and Baler Interface Harness Routing and Connections
Installation of iPad Integration Control
Locate a safe location in the cab of the tractor to place the iPad Integration Control (030-6672C). Recommended location is securely fastened out of the operators way in a location that is close enough to reach with the iPad cord.
Connect the Power / Communication harness (006-6650TM(E)) to the bottom of the receiver. To operate the applicator, plug the iPad cord into the communication port indicated by:
iPad Integration Control Light Signals
Green Slow Blink Power supplied to the applicator system and the unit is going through its startup process. This will take approximately 25-35 seconds. Green Double Blink Indicating the iPad module recognizes the iPad but the app is not open or connected. Green Solid Light Module is connected to the app and is ready to operate. *Recommended to use the USB cable included with the applicator kit (006-6672USBC) **600 Series Applicators with serial number before DCP27000 will require the DCP to be sent to Harvest
Tec for a required update in order to use the iPad Integration Module (030-6670C).
Bluetooth Receiver Lights
Pre-2020 applcaitors equipped with Bluetooth receivers (030-6672B) are now equipped with lights to indicate both power and Hay App connection on the Apple iPad. Clean light regularly Blinking Lights System is waiting for the processor to connect, which could take up to 35 seconds. Red Light The Bluetooth receiver has power Green Light The Bluetooth receiver is connected to the Hay App.
Wiring Diagram
- A. The Baler Power/Communication Harness (006-6650LS2) will attach to the open port of the Tractor Harness (006-6650TM) and run back to the Dual Channel Processor (006-6671LS). Connect the large plug of the Baler Power/Communication Harness (006-6650LS) to the bottom (shorter side) of the DCP.
- B. Attach the Baler Interface Harness (006-6650VA) in between the short whip cable hardwired to the DCP and the main Power/Communication Harness (006-6650LS2). Make sure Active Terminator removed from the top of the baler processor is attached to Baler Interface Harness (006-6650VA).
- C. Install green terminator (006-5650Z) to the port labeled Modular Port on the Pump Controller (006-5672).
- D. Attach moisture / bale rate harness (006-7303H) and end of bale harness (006-7400) to the DCP (006-6671LS).
- E. Attach Pump Control Harness (006-5650F3M) between Pump Controller (006-5672) and DCP (006-6671LS).
- F. Connect Keyed Power Extension harness (006-5650K) to a keyed power source.
- G. Connect the iPad Integration Control (030-6672C) to the Communication Harness (006-6650TM).
Note: The Optional Port and the Data Transfer Port are not used in this application.
*AGCO 2100 Series Balers Pre 2012 will need the Integration Harness 006-6650VAX
Pin Outs
Parts Breakdown
(Converting a 500 Series to a 600 Series)
Notes
Harvest Tec Inc. Warranty and Liability Agreement
Harvest Tec, Inc. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, Inc. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, Inc.
Our obligation under this warranty is limited to repairing or replacing free of charge to the original purchaser any part that in our judgment shows evidence of defective or improper workmanship, provided the part is returned to Harvest Tec, Inc. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. Parts must be returned through the selling dealer and distributor, transportation charges prepaid.
This warranty shall not be interpreted to render Harvest Tec, Inc. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays or any expense prospective profits or for any other reason. Harvest Tec, Inc. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship.
There are no warranties, either expressed or implied, of merchantability or fitness for particular purpose intended or fitness for any other reason.
This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, Inc. will not affect our ability to obtain materials or manufacture necessary replacement parts.
Harvest Tec, Inc. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold. Revised 4/17
HARVEST TEC, INC. P.O. BOX 63
2821 HARVEY STREET HUDSON, WI 54016
PHONE: 715-386-9100 1-800-635-7468
FAX: 715-381-1792
Email: info@harvesttec.com