ADLER AD 2836 Professional Trimmer User Manual

by 
ADLER AD 2836 Professional Trimmer 
User Manual

 

ADLER AD 2836 Professional Trimmer User Manual

 

ADLER AD 2836 Professional Trimmer - overview

SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

The warranty conditions are different, if the device is used for commercial purpose.

  1. Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
  2. The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
  3. The applicable voltage is 230V, ~50Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
  4. Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
  5. WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their
    safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over
    8 years of age and these activities are carried out under supervision.
  6. After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
  7. Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
  8. Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
  9. Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
  10. Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
  11. Never use the product close to combustibles.
  12. Do not let cord hang over edge of counter or touch hot surfaces.
  13. Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
  14. In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
  15. close to water icon Never use this device close to water, e.g.: Under shower, in bath tube, or above sink filled with water.
  16. If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off.
  17. Do not allow the device or power adaptor to wet. If the device falls into water, imediately remove the power plug or power adaptor from the socket. If the device is powered, do not put hands in the water. Have the device checked by the qualified electrician before using it again.
  18. Do not touch the device or power adaptor with wet hands.
  19. The device has to be turned off after every use.
  20. Do not leave the unit attached to the wall outlet or power supply unit unattended.
  21. If the device utilises a power adaptor, do not cover it, because this can cause a dangerous temperature rise and can damage the device. Always connect the power adaptor cable to the device, and then connect the power adaptor to the power socket.
  22. Keep the device out of the reach of children. Using the devices by children must be supervised by adults.
  23. The device is designed only for cutting natural human hair.
  24. The cutting blades are very sharp. Be careful during assembly, disassembly and cleaning. Do not touch the blades moving parts during operation!
  25. Do not wash the blades in water.
  26. Change the attachments only when the unit is turned off.
  27. Use only original accessories.
  28. To remove hair from inside the machine, use only the included brush.
  29. Do not use the device in the bath.
  30. Do not use the device on people who are sleeping.
  31. During operation, do not place the device on wet surfaces or clothes.
  32. The device is not designed to work with external schedulers or separate remote control system.

DESCRIPTION OF THE DEVICE

  1. Power switch
  2. Clipping head
  3. Power / Charging light
  4. Cutting length attachments (1.5mm, 3mm, 4.5mm, 6mm.)
  5. Protection cover
  6. Oil
  7. Cleaning brush
  8. USB cable.
  9. Charging port

BATTERY CHARGING

Before use, charge the battery. To begin charging, connect the power cord (9) to the devices Charging port and the USB cableto the charger or other USB compatible device. Is using the charger plug it into an 5V 1A mains outlet. The charging icon will light up . A fully charged battery is sufficient for up to 240 minutes of continuous operation. After charging, remove the charger from the power source. When the device is not used for a long time please recharge. Recharge it at least once every 6 months to maintain adequate battery capacity.

USING THE DEVICE

Depending on the needs install the appropriate trimmer attachment as shown in Figure B. To remove it follow the Figure B in reverse order.

Blade removal:

Using a Philips screwdriver (cross shaped) unscrew the 2 screws from the blade as shown on picture D. Take a new blade and place it in the same position as the previous blade. Making sure the holes and inside parts are correctly assembled screw the blade into place using
the same screws. Turn on the device to check if the blade is working correctly before use. Please check if the blades are parallel to each other.

CLEANING

Disconnect the device from the power supply. Remove the attachment from the head. Clear the blades with the supplied brush. After cleaning, there should be no hair between the blades. After every few haircuts, oil the cutting head pouring 2 to 3 drops of the supplied oil into the space between the fixed blade and the movable blade. Install the Protection Cover (6). Clean the housing with a dry or slightly damp cloth.

TECHNICAL DATA

Power supply: 5V 1A Power supply icon

Device is made in class II of insulation.
Device is compliant with EU directives:
– Low voltage directive (LVD)
– Electromagnetic compatibility (EMC)
Device marked CE mark on rating label

 

disposal icon To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.