Control-Tec EP-800 Epsilon EP Programmable Servo Drive User Manual

Control-Tec EP-800 Epsilon EP Programmable Servo Drive User Manual

EP-800 User Manual

Table of Contents

Product identification

Product name: EP-800
Model number: EP-800
Manufacturer Name: Control-Tec, LLC d/b/a Aptiv Connected Services
Manufacturer Address: 5725 Innovation Drive
Troy, Michigan 48098
United States of America

Intended Use

The EP-800 is used in or on a vehicle to collect test data to support validation testing.

Safety Information

General Safety Warnings

Read this manual before using the device.
Keep away from water and heat sources.
Do not disassemble or modify the device.
Do not insert objects into the reset port.

Radio Frequency Safety

Maintain minimum separation distance from body (e.g., 20 cm).
Complies with FCC, ISED, and EU RF exposure limits.

Electrical Safety

Intended for use on vehicles with 12V or 24V architectures.

Technical Specifications

Frequency Bands (all)

BT: 2.4 GHz
Wi-Fi: 2.4 GHz and 5 GHz
GSM:B2, B3, B8, B8
WCDMA: B1, B2, B4, B5, B6, B8, B19
LTE: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41

Frequency Bands (EU)

BT: 2.4 GHz
Wi-Fi: 2.4 GHz and 5 GHz
GSM:900, 1800
WCDMA: B1, B5, B8
LTE: B1, B3, B5, B7, B8, B20, B28, B38, B40

Power Levels (EU)

Restrictions

Operations in the 5150 – 5350 MHz band are restricted to indoor use only for jurisdictions listed
below.

Wi-Fi

2.4 GHz
- 2414 – 2472 MHz
- 20.61 dBm (115.08 mW) EIRP
5 GHz
- 5170 – 5330, 5490 – 5610 MHz
- 21.73 dBm (148.94 mW) EIRP

Cellular

Max Power: 30.89 dBm (1227.44mW) EIRP
LTE
- FDD: 703 – 2570 MHz
- TDD: 2300 – 2620 MHz
GSM
- 880 – 1785 MHz
WCDMA
- 824– 1980 MHz

Bluetooth

2.4 GHz

2402 – 2480 MHz
10.22 dBm (10.52 mW) EIRP

Supported Wireless Technologies

Wi-Fi
BT
Cellular

GNSS Bands

GPS
GLONASS
BeiDou
Galileo

Input Power

Typical Architecture: 12V or 24V
Voltage Limits: 7.5 VDC – 32 VDC
Typical Power: 3.6W
Max Power: 18W

Temperature Limits

Full Functionality: -40°C to 50°C
Limited Functionality: 50°C to 70°C

IP Rating

IP68

Installation and Setup

Consult the Installation guide and/or speak with your local Aptiv representative.
Only connect with cables approved for the EP-800. Do not use cables intended for the CT-1000/EP-1000.

Regulatory Information

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by Aptiv could void the user‘s authority to operate the equipment.
This device complies with Industry Canada license-exempt RSS standard(s) and with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FCC and ISED (Innovation, Science and Economic Development Canada) require a minimum separation distance of 20 centimeters (7.87 inches) between certain radio transmitting equipment and the human body to comply with RF exposure limits. Do not throw in household waste.
This device has been designed to operate with the antennas listed below, and
having a maximum gain listed below for each antenna in each band. Antennas not
included in this list or having a gain greater than shown for each antenna and band
are strictly prohibited for use with this device. The required antenna impedance is
50 ohms.
- - - WLAN Primary: Quectel Y2RSU0HA0DA (1.2 dBi @ 2GHz band; 4 dBi @ 5GHz band)
    - WLAN Div/BT: Quectel Y2RSU0HA0CA (3.6 dBi @ 2GHz band; 2.7 dBi @ 5GHz band)
ANATEL: HHHHH-YY-FFFFF

Warranty and Support

Each item of purchased hardware and its media shall be new and shall be free from defects in manufacture, materials, and design, and shall function properly under ordinary use and operate in conformance with its applicable specifications and documentation for a period of one (1) year from the applicable acceptance date (the “Warranty Period”) of such purchased hardware. Any non-customer induced failure will be replaced with equivalent new hardware within a reasonable timeframe, typically within 1 month of reported failure.

For leased hardware, the customer is responsible for returning each unit and related accessories within thirty working days of testing completion and returning each unit in a functional state. If leased hardware is not returned within thirty days of the end of the test or is returned damaged, the customer may be invoiced at the standard hardware purchase price plus ten percent. The customer is responsible for all data usage charges including cellular or Wi-Fi, and for any cellular roaming charges that occur. International roaming will be disabled unless the customer instructs otherwise. The customer is responsible for all shipping and travel charges associated with returning leased hardware, and such charges may be billed at cost plus ten percent.