Safety Instructions
This oven must only be installed by a suitably qualified and licenced person and in accordance with the instructions provided. Incorrect installation may cause harm to persons, damage property and void the product’s warranty.
IMPORTANT!
The power supply to the oven must be cut off before any adjustments or maintenance work is undertaken.
WARNING
When using this product, basic precautions should always be taken including the following:
► This oven is designed for domestic household use and for the cooking of domestic foodstuffs.
IMPORTANT!
Your built-in oven is an electrical appliance and as with any electrical appliance (particularly with electric heating elements), basic precautions must be followed in order to reduce the risk of fire, burns, electrical shocks and/or other serious injuries or even death.
► The appliance becomes hot during operation. Take care not to touch the hot parts inside the oven.
► This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
► Children should be supervised to ensure that they do not play with the appliance.
► While in operation direct contact with the oven may cause burns!
► Ensure that small items of household equipment, including connection leads, do not touch the hot oven as the insulation material of this equipment is usually not resistant to high temperatures.
► Do not leave the oven unattended when cooking. Oils and fats may catch fire due to overheating.
► Do not put pans on the opened door of the oven.
► Do not use harsh cleaning agents or sharp metal objects to clean the door as they can scratch the surface, which could then result in the glass cracking.
► Do not use the oven in the event of a technical fault. Any faults must be fixed by an appropriately qualified and authorised Residentia Group service agent. Refer to the warranty section at the rear of this user manual.
► In the event of any incident caused by a technical fault, disconnect the power and report the fault to the service centre to be repaired.
► The rules and provisions contained in this instruction manual should be strictly observed.
► Do not allow anybody who is not familiar with the contents of this instruction manual to operate the oven.
► The oven should not be cleaned using steam-cleaning equipment, as damage can occur to the inner electrical components.
► The panels adjacent to the oven must be made of heatresistant material, or heat deflectors installed.
► Cabinets with a veneer exterior must be assembled with glues, which can withstand temperature of up to 100 degrees Celsius.
► Keep combustible materials such as: curtains, drapes, furniture, pillows, clothing, linens, bedding, paper, etc. at least 900mm from the front sides and rear of the oven.
► Do not use this oven in areas where fuel, paint or other flammable liquids or their associated vapours may be present.
► To reduce the risk of fire, do not place or install this oven in areas where the ventilation or circulation ducts may become blocked.
► The oven’s power cord must be connected to a properly grounded and protected, 220-240V electrical outlet. Always use ground fault protection where required by the electrical code.
► This oven is hard-wired and an extension cord should not be used.
► When transporting or storing the unit, keep it in a dry location, free from dust, excessive vibration or other factors, which may damage the unit.
► Do not operate any oven with a damaged cord or plug, after the heater malfunctions or has been dropped or damaged in any manner. Return the oven to an authorised Residentia Group service centre to be checked.
► If the supply cord is damaged, it must be replaced by a special cord or assembly available from Residentia Group or its authorised service agent.
► Use this oven only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
► Never add cold water to food on a hot universal tray or baking tray or directly onto food in a hot oven. The steam created could cause serious burns or scalding and the sudden change in temperature can damage the enamel.
► Do not lift the oven by the handle.
DECLARATION OF CONFORMITY
This appliance complies with the following Australian/European Directives:
— 2006/95/CE General regulations / Low tension
— 1935/2004/CE 90/128/EEC This appliance is suitable to come in contact with food
— 2004/108/CE Electromagnetic compatibility
— Low voltage – 73/23
— Safety standards – EN 60335-1, EN30-1-1, AS/NZS 3350-1,3350-2-6, AS/NZS 60335.2.6:2014
The manufacturer declares that the oven is built using certified materials and requires the appliance to be installed in accordance with the standards currently in force. This oven should only be used by a trained person and for domestic purposes only.
UNPACKING
During transportation, protective packaging was used to protect the appliance against any damage. After unpacking, please dispose of all elements of packaging in a way that will not cause damage to the environment. All materials used for packaging the appliance are environmentally friendly; they are 100% recyclable and are marked with the appropriate symbol.
► During unpacking, the packaging materials (polythene bags, polystyrene pieces, etc.) should be kept out of reach of children.
DISPOSAL OF THE APPLIANCE
Old appliances should not simply be disposed of with normal household waste, but should be delivered to a collection and recycling centre for electric and electronic equipment. A symbol shown on the product, the instruction manual or the packaging shows that it is suitable for recycling.
Materials used inside the appliance are recyclable and are labelled with information concerning this. By recycling materials or other parts from used devices you are making a significant contribution to the protection of our environment.
Information on appropriate disposal centres for used devices can be provided by your local authority.
Your InAlto Oven
CONTROLS & COMPONENTS
KEY
—
1. Oven function selection knob
2. Minute-minder (timer)
3. Temperature control knob
4. Baking tray
5. Grilling rack
6. Grilling shelf
Installing Your Oven
It’s important to carefully read the following installation instructions before beginning the installation of your oven.
IMPORTANT!
The connection of this oven must be carried out by a suitably qualifi ed and licensed person, in accordance with the current versions of the following:
► AS/NZS 3000 Wiring Rules
► Electricity Safety Regulations 2010
► The installation instructions within this user manual
Note: Ensure there is a grounded socket nearby (behind the unit). A dedicated power circuit is recommended for the unit but not required. Additional electrical appliances on the same circuit may exceed the current (amperage) rating for that circuit. If after the installation of your unit the circuit breaker trips or the fuse fails on a repeated basis then a dedicated circuit will likely be required.
POSITIONING
The adjacent cabinetry and wall materials must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room.
► The kitchen area should be dry and equipped with suffi cient ventilation. When installing the oven, easy access to all control elements should be ensured.
► This is a built-in oven and has been designed to be housed within an oven cabinet. Coating or veneer used on cabinetry must be applied with a heat resistant adhesive (rated to 100°c). This prevents surface deformation or detachment of the coating. In the case
of vinyl wrap kitchens, it is strongly recommended to have heat defl ectors installed on either side of the oven cabinet.
► Your oven cabinet should be made to suit the following dimensions and can be either a tall or underbench cabinet to suit your kitchen design.
► Make sure that the electrical circuit is disconnected or fuse removed, then connect the oven into the mains supply. Important! As this appliance is hard-wired, the installation/connection should only be completed by a licensed electrician.
► Insert the oven completely into the oven cabinet and use the four screws supplied to fi x the oven into place (refer to the diagram below).
Note. It is a requirement for a ventillation gap to be cut into the oven cabinet as per the diagrams on this page.
INSTALLATION
WARNING!
The installation must be carried out by a suitably qualified and licensed person and in accordance with the current standards.
Fitting guidelines
► The oven is manufactured to work with three-phase alternating current (220V–240V/50Hz). The connection diagram is also found on the cover of the connection box.
Remember:
► The connection wire should match the connection type and the power rating of the oven.
► The connection cable must be secured in a strain-relief clamp.
WARNING!
Remember to connect the safety circuit to the connection box terminal marked with . The electricity supply for the oven must have a safety switch which enables the power to be cut off in the case of an emergency. The distance between the working contacts of the safety switch must be at least 3mm.
Before connecting the oven to the power supply it is important to read the information on the data plate and the connection diagram.
Operating Your Oven
BEFORE THE FIRST USE
► Remove all packaging and clean the interior of the oven.
► Take out and wash the oven fittings with warm soapy water.
► Switch on any ventilation within the room(such as a rangehood), or open any windows.
► Heat the oven to a temperature of 250° C for approximately 30–45 minutes.
Note: There may be strong odour during the first use, which is the burning off of any chemical residues from its construction. This is normal for all ovens.
IMPORTANT!
The inside of the oven should only be washed with warm water and a small amount of washing up liquid.
IMPORTANT!
In order for the oven to operate, you must:
► Select the required conditions of the oven.I.e. the temperature and a mode of heating.
► Set the knob to the required position, turning it to the right (clockwise).
FAST START FEATURE
Your Inalto oven is equipped with a fast start function which can be used to bring your oven up to 150° C in approximately 4 minutes.
To use this feature:
► Set the oven function knob to the position of “Fan assisted Bottom & Central elements”.
► Set the temperature knob to 150° C (or lower if desired).
► Once the oven is at temperature, the “Oven Heating” indicator (Indicator D) will switch off.
USE OF THE GRILL
Your Inalto oven grills through the use of infrared rays emitted by the incandescent grill heater.
IMPORTANT!
You should always use the grill function with the door shut. When the grill is in use with the oven door open, accessible parts can become hot and damage can be done to the controls.
In order to use the grill:
► Set the oven function knob to one of the grill functions.
► Heat the oven for approximately 4-5 minutes.
► Insert a tray with your dish onto the appropriate cooking shelf.
Note: The grill function can be used upto a maximum of 250° C, whilst the “Grill and fan assist” function can be used at a maximum of 200° C.
Cleaning & Maintenance
By ensuring proper cleaning and maintenance of your Inalto oven, you can ensure that it will have a long and fault free operation.
WARNING!
Do not start cleaning the oven until it has completely cooled.
► Typically you should only ever need to clean your oven with warm soapy water, or light cleaning products to assist with the removal of fat or oil emulsions.
► Your oven should be cleaned after every use and you can use the “Light” function to assist with visibility.
► After cleaning your oven chamber, you should wipe it dry.
CLEANING THE GLASS
► Glass surfaces on the door and control panel should be cleaned immediately after soiling, using a damp cloth.
► Oven cleaners may be used to remove stubborn stains and built-up residues.
► Avoid the use of harsh abrasive cleaners and sharp metal scrapers as they can scratch or damage the surface.
CLEANING THE STAINLESS STEEL
All grades of stainless steel can stain or discolour and you must regularly ensure it’s kept clean using the following procedures:
► Start by using clean, warm soapy water. For stubborn stains or discolouration, you can try stainless steel cleaners available from the supermarket.
► Be careful when cleaning the stainless steel, as there may be sharp edges.
► DO NOT use abrasive or harsh solvent cleaners.
CLEANING THE OVEN/GRILL
► Always keep the internal of the oven clean, ensuring that fats and oils don’t accumulate around the elements or fan.
► Always keep the oven dish, baking trays and grill dish inserts clean as any deposits may catch fire or smoke.
► Always wrap your meats in aluminium foil or use a covered oven-roasting dish to minimise required cleaning.
DOOR REMOVAL
In order to obtain easier access to the oven chamber for cleaning, it is possible to remove the door.
To do this:
► Tilt the safety catch part of the hinge upwards.
► Close the door lightly, lift and pull it out towards you.
► In order to fit the door back on to the oven, do the reverse.
When fitting, ensure that the notch of the hinge is correctly placed on the protrusion of the hinge holder. After the door is fitted to the oven, the safety catch should be carefully lowered down again. If the safety catch is not set it may cause damage to the hinge when closing the door.
REMOVAL OF THE INTERNAL GLASS PANEL
Unscrew and unfasten the plastic latch that is in the corner at the top of the door. Next take out the glass from the second blocking mechanism and remove. After cleaning, insert and block the glass panel, and screw in the blocking mechanism.
REPLACEMENT OF THE OVEN LIGHT GLOBE
Warning!
In order to avoid the possibility of an electric shock, 58ensure that the appliance is switched off at the isolator switch, before removing the light globe.
► Set all control knobs to the off position and switch the oven off at the isolator switch.
► Unscrew the Light Globe cover. Unscrew the blown light globe.
► Replace the globe with a new oven globe with the following parameters:
► Voltage: 230v
► Power: 25W
► E14 Oven globe
► Screw the Light Globe cover back into place.
Troubleshooting & Technical Data
OPERATION IN CASE OF EMERGENCY
In the event of an emergency you should:
► Switch off all oven controls
I.e. the cooking function and temperature
► Switch the oven off at the isolation switch or at the fuse box.
► Call the Residentia Support Team on: 1300 11 HELP (4357).
Some minor faults can be fixed by referring to the instructions given in the Troubleshooting section below. There is also a self-help section online at:http://www.residentiagroup.com.au
TROUBLESHOOTING
TECHNICAL DATA
Warranty Information
WARRANTY TERMS & CONDITIONSCOOKING APPLIANCES(BUILT-IN OVENS, COOKTOPS)
This document sets out the terms and conditions of the product warranties for Residentia Group Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should you require service for your Appliance.
1. IN THIS WARRANTY
(a) ‘acceptable quality’ as referred to in clause 10 of this warranty has the same meaning referred to in the ACL;
(b) ‘ACL’ means Trade Practices Amendment (Australian Consumer Law) Act (No.2) 2010;
(c) ‘Appliance’ means any Residentia Group product purchased by you accompanied by this document;
(d) ‘ASR’ means Residentia Group authorised service representative;
(e) ‘Residentia Group’ means Residentia Group Pty Ltd of 165 Barkly Ave, Bunrley VIC 3121, ACN 600 546 656 in respect of Appliances purchased in Australia;
(f ) ‘major failure’ as referred to in clause 10 of this warranty has the same meaning referred to in the ACL and includes a situation when an Appliance cannot be repaired or it is uneconomic for Residentia Group, at its discretion, to repair an Appliance during the Warranty Period;
(g) ‘Warranty Period’ means:
(i) where the Appliance is used for personal, domestic or household use (i.e. normal single family use) as set out in the instruction manual, the Appliance is warranted against manufacturing defects for 24 months, following the date of original purchase of the Appliance;
(h) ‘you’ means the purchaser of the Appliance not having purchased the Appliance for re-sale, and ‘your’ has a corresponding meaning.
2. This warranty only applies to Appliances purchased and used in Australia and is in addition to (and does not exclude, restrict, or modify in any way) any nonexcludable statutory warranties in Australia.
3. During the Warranty Period Residentia Group or its ASR will, at no extra charge if your Appliance is readily accessible for service, without special equipment and subject to these terms and conditions, repair or replace any parts which it considers to be defective.
Residentia Group or its ASR may use remanufactured parts to repair your Appliance. You agree that any replaced Appliances or parts become the property of Residentia Group. This warranty does not apply to light globes, batteries, filters or similar perishable parts.
4. Parts and Appliances not supplied by Residentia Group are not covered by this warranty.
5. You will bear the cost of transportation, travel and delivery of the Appliance to and from Residentia Group or its ASR. If you reside outside of the service area, you will bear the cost of:
(a) travel of an authorised representative;
(b) transportation and delivery of the Appliance to and from Residentia Group or its ASR, in all instances, unless the Appliance is transported by Residentia Group or its ASR, the Appliance is transported at the owner’s cost and risk while in transit to and from Residentia Group or its ASR.
6. Proof of purchase is required before you can make a claim under this warranty.
7. You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship. Residentia Group is not liable in the following situations (which are not exhaustive):
(a) the Appliance is damaged by:
(i) accident
(ii) misuse or abuse, including failure to properly maintain or service
(iii) normal wear and tear
(iv) power surges, electrical storm damage or incorrect power supply
(v) incomplete or improper installation
(vi) incorrect, improper or inappropriate operation
(vii) insect or vermin infestation
(viii) failure to comply with any additional instructions supplied with the Appliance;
(b) the Appliance is modified without authority from Residentia Group in writing;
(c) the Appliance’s serial number or warranty seal has been removed or defaced;
(d) the Appliance was serviced or repaired by anyone other than Residentia Group, an authorised repairer or ASR.
8. This warranty, the contract to which it relates and the relationship between you and Residentia Group are governed by the law applicable where the Appliance was purchased.
9. To the extent permitted by law, Residentia Group excludes all warranties and liabilities (other than as contained in this document) including liability for any loss or damage whether direct or indirect arising from your purchase, use or non use of the Appliance.
10. For Appliances and services provided by Residentia Group in Australia, the Appliances come with a guarantee by Residentia Group that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Appliance repaired or replaced
if the Appliance fails to be of acceptable quality and the failure does not amount to a major failure. The benefits to you given by this warranty are in addition to your other rights and remedies under a law in relation to the Appliances or services to which the warranty relates.
11. At all times during the Warranty Period, Residentia Group shall, at its discretion, determine whether repair, replacement or refund will apply if an Appliance has a valid warranty claim applicable to it.
12. To enquire about claiming under this warranty, please follow these steps:
(a) carefully check the operating instructions, user manual and the terms of this warranty;
(b) have the model and serial number of the Appliance available;
(c) have the proof of purchase (e.g. an invoice) available;
(d) telephone the numbers shown below.
13. You accept that if you make a warranty claim, Residentia Group and its ASR may exchange information in relation to you to enable Residentia Group to meet its obligations under this warranty.
IMPORTANT
Before calling for service, please ensure that the steps in point 12 have been followed.
Telephone Contact
► Service: Please call 1300 11 HELP (4357)
TEL. 1300 11 4357
http://SU P P O RT@ R E SI D E N T I AG RO U P.C O M. AU
http://WWW.RESIDENTIA.GROUP